<kuid2:368725:25038:5> NSWGR water crane 2, 8ft jib with bi-directional swing, no fixed tracks

Тип: Индустрия
Опубликовано: 6.06.2024 16:17:32
Скачиваний: 19
Размер: 6.9 MB

Скачать

A water crane designed by New South Wales Government Railways with a valve operable from from the end of the jib. Modelled on cranes in use at Moss Vale in the 1950s.
In game, an engine can stay attached to a consist while watering.
The jib length is 8ft, so the separation between track centres served by the crane is 16ft.
There are no fixed tracks. Instead the user must place a trackmark on each of the track splines that pass on either side of the water column. The trackmarks must point toward the crane jib. Blue Surveyor-only wedges enable precise positioning of the trackmarks.
Given the localised name of the water column is 'myName', the trackmarks must be named <myName> + '-mark-acw' and <myName> + '-mark-cw'.
Trackmark <myName> + '-mark-acw' is located adjacent to the column of the water crane on the track serviced by an anti-clockwise swing of the jib. Trackmark <myName> + '-mark-cw' is located adjacent to the column on the track on the opposite side of the crane.
Adjust the trigger radii of the trackmarks to 6m.
When placing the crane on track with a non-zero gradient, the model may be rolled (hold down SHIFT key while using the ROTATE button, also hold down CTRL button for fine adjustemnt) to match the gradient up to a limit of 2% percent (1 in 50).
The crane's arm is animated. It will rotate anti-clockwise (track-acw) or clockwise (track-cw) by 90 degrees or 38 degrees depending on whether the loco's water port is centrally located (standard) or on a side tank, respectively. The presence of a side tank port is indicated to the water crane script by use of a 'yes' value for a 'lsp_side-tank' tag in the 'extensions' container of the vehicle's config file.
If accurate alignment between the water crane and the loco's water port is to be achieved, the longitudinal offset (metres) from the vehicle's pivot point (main mesh origin) and its water port must be specified by a 'lsp_offset_water' tag in the vehicle's extensions container.
For locos under player control, the player should spot a tender's water port adjacent to the crane's column or at the column-facing edge of the drain grill for a side-tank engine.

config.txt:

kuid                                    <kuid2:368725:25038:5>
username                                "NSWGR water crane 2, 8ft jib with bi-directional swing, no fixed tracks"
description                             "A water crane designed by New South Wales Government Railways with a valve operable from from the end of the jib. Modelled on cranes in use at Moss Vale in the 1950s.
In game, an engine can stay attached to a consist while watering.
The jib length is 8ft, so the separation between track centres served by the crane is 16ft. 
There are no fixed tracks. Instead the user must place a trackmark on each of the track splines that pass on either side of the water column. The trackmarks must point toward the crane jib. Blue Surveyor-only wedges enable precise positioning of the trackmarks.
Given the localised name of the water column is 'myName', the trackmarks must be named <myName> + '-mark-acw' and <myName> + '-mark-cw'.
Trackmark <myName> + '-mark-acw' is located adjacent to the column of the water crane on the track serviced by an anti-clockwise swing of the jib. Trackmark <myName> + '-mark-cw' is located adjacent to the column on the track on the opposite side of the crane.
Adjust the trigger radii of the trackmarks to 6m.
When placing the crane on track with a non-zero gradient, the model may be rolled (hold down SHIFT key while using the ROTATE button, also hold down CTRL button for fine adjustemnt) to match the gradient up to a limit of 2% percent (1 in 50).
The crane's arm is animated. It will rotate anti-clockwise (track-acw) or clockwise (track-cw) by 90 degrees or 38 degrees depending on whether the loco's water port is centrally located (standard) or on a side tank, respectively. The presence of a side tank port is indicated to the water crane script by use of a 'yes' value for a 'lsp_side-tank' tag in the 'extensions' container of the vehicle's config file.
If accurate alignment between the water crane and the loco's water port is to be achieved, the longitudinal offset (metres) from the vehicle's pivot point (main mesh origin) and its water port must be specified by a 'lsp_offset_water' tag in the vehicle's extensions container.
For locos under player control, the player should spot a tender's water port adjacent to the crane's column or at the column-facing edge of the drain grill for a side-tank engine."
author                                  "Leigh Stokes (ElStoko)"
kind                                    "industry"
trainz-build                            4.2
category-class                          "BIN"
category-region                         "AU"
category-era                            "1910s;1920s;1930s;1940s;1950s;1960s"
script                                  "water_crane_v16_nft"
class                                   "water_column"
height-range                            -1,1
rollstep                                0.1
rotate-yz-range                         -2,2
mesh-detail-level-count                 4
extensions
{
  jib-support-wheel                     "true"
  restraining-chain                     "true"
  jib-end-control                       "true"
}
mesh-table
{
  default
  {
    mesh                                "default.im"
    auto-create                         1
    effects
    {
      trackmark1
      {
        kind                            "attachment"
        att                             "a.trackmark_acw"
        default-mesh                    <kuid:368725:90047>
        surveyor-only                   1
      }
      trackmark2
      {
        kind                            "attachment"
        att                             "a.trackmark_cw"
        default-mesh                    <kuid:368725:90047>
        surveyor-only                   1
      }
    }
  }
  main_lod0
  {
    mesh                                "main_0.im"
    auto-create                         1
    lod-level                           0
  }
  main_lod1
  {
    mesh                                "main_1.im"
    auto-create                         1
    lod-level                           1
  }
  main_lod2
  {
    mesh                                "main_2.im"
    auto-create                         1
    lod-level                           2
  }
  main_lod3
  {
    mesh                                "main_3.im"
    auto-create                         1
    lod-level                           3
  }
  chain_lod0
  {
    mesh                                "chain_0.im"
    auto-create                         1
    lod-level                           0
  }
  chain_lod1
  {
    mesh                                "chain_1.im"
    auto-create                         1
    lod-level                           1
  }
  chain_lod2
  {
    mesh                                "chain_2.im"
    auto-create                         1
    lod-level                           2
  }
  jib
  {
    mesh                                "jib.lm"
    anim                                "jib.kin"
    auto-create                         1
  }
  jib-wheel
  {
    mesh                                "jib-wheel.lm"
    anim                                "jib-wheel.kin"
    auto-create                         1
    att                                 "a.jibwheel"
    att-parent                          "jib"
  }
  gears
  {
    mesh                                "gears.lm"
    anim                                "gears.kin"
    auto-create                         1
  }
  jib-valve-control
  {
    mesh                                "jib-valve-control.lm"
    anim                                "jib-valve-control.kin"
    auto-create                         1
  }
}
queues
{
  water
  {
    size                                100000
    initial-count                       100000
    product-kuid                        <kuid:-3:10004>
    allowed-products
    {
      0                                 <kuid:-3:10004>
    }
  }
}
processes
{
  generate_water
  {
    start-enabled                       1
    duration                            60
    inputs
    {
    }
    outputs
    {
      0
      {
        amount                          1000
        queue                           "water"
      }
    }
  }
}
thumbnails
{
  0
  {
    image                               "thumbnail.jpg"
    width                               240
    height                              180
  }
}
string-table
{
  track-acw                             "Take water at track served by ACW jib swing"
  track-cw                              "Take water at track served by CW jib swing"
}
kuid-table
{
  water                                 <kuid:-3:10004>
  blue-wedge                            <kuid:368725:90047>
}

Файлы:

chain_2.im	840 B
gears.lm.txt	228 B
jib-valve-control.lm.txt	202 B
default.im	9.1 kB
gears.kin	17.0 kB
jib-valve-control.kin	17.0 kB
jib-wheel.lm.txt	186 B
jib-wheel.kin	17.0 kB
gears_2.im	32.8 kB
jib-valve-control_1.im	24.8 kB
jib.lm.txt	222 B
jib-valve-control_0.im	57.4 kB
gears_1.im	59.4 kB
jib-wheel_1.im	18.2 kB
jib.kin	17.0 kB
gears_0.im	72.7 kB
chain_1.im	86.4 kB
jib-wheel_0.im	48.8 kB
jib_2.im	17.1 kB
jib_1.im	55.6 kB
main_3.im	34.9 kB
watercrane-watercrane.texture.txt	55 B
chain_0.im	138.2 kB
thumbnail.jpg	33.3 kB
jib_0.im	74.3 kB
watercrane_normal-watercrane_normal.texture.txt	94 B
water_crane_v16_nft.gs	34.2 kB
main_2.im	137.1 kB
main_1.im	202.7 kB
main_0.im	261.6 kB
watercrane.tga	8.0 MB
watercrane_normal.tga	8.0 MB
Общий объём файлов:	17.4 MB

Версии элемента:

kuid	kind	name	build	date	size
<kuid2:368725:25038:5>	industry	NSWGR water crane 2, 8ft jib with bi-directional swing, no fixed tracks	4.2	6.06.2024 16:17:32	6.9 MB
<kuid2:368725:25038:3>	industry	NSWGR water crane 2, 8ft jib with bi-directional swing, no fixed tracks	4.2	14.05.2023 15:01:36	6.9 MB
<kuid2:368725:25038:2>	industry	NSWGR water crane 2, 8ft jib with bi-directional swing, no fixed tracks	4.2	18.10.2021 19:06:27	6.9 MB

Зависимости:

kuid	author	kind	name	build	date	size
<kuid:-3:10004>	#-3	product	Вода	0	20.10.2022 23:31:06	5.6 kB
<kuid2:368725:90047:1>	#368725	mesh	Track mark outline	3.7	24.06.2020 14:18:45	5.2 kB
Всего связей: 2, неизвестных связей: 0

Зависимые элементы:

kuid	author	kind	name	build	date	size
Нет